Objective: To separate management traffic from data/customer traffic on your Cisco Catalyst 4500 L3 Switch Preferably, Data and Management are into 2 separate network domains. Pre-requisite: UTP cable to connect to management port (via FastEthernet 1) and the other end is connected to a network switch to access the OOB management gateway Tested on Cisco IOS Version 15.1 (Cisco Catalyst 4948E) * * Management IP Configuration* * 1. Configure the vrf for management vrf definition management ! address-family ipv4 exit-address-family ! address-family ipv6…
Tag: <span>SNMP</span>
Objective: To separate management traffic from data/customer traffic in your Huawei Routers Preferably, Data and Management are into 2 separate network domains. Pre-requisite: UTP cables (for each MPU management port in case for switchover) are connected to a network switch to access the OOB management gateway To go configuration mode: system-view To preview configuration change before commiting display configuration candidate * * Management IP Configuration* * a. Configure the vpn instance for management ip vpn-instance <vpn instance name> description <description> ipv4-family b. Set…
Here’s the SNMP configuration examples for Huawei routers. Taking the following details: SNMP community: snmpcomm123 Loopback/management IP address: 192.168.10.100 SNMP Polling Server: 192.168.20.199 SNMP Trap Server: 192.168.20.200 Pre-config: (assuming Loopback0 is your source interface to send those SNMP traffic) interface LoopBack0 description _ Loopback for Huawei Router ip address 192.168.10.100 255.255.255.255 SNMPv2c Polling: 1. Configure SNMP (version can be set to all to support v1,v2c and v3) snmp-agent sys-info version all 2. Configure SNMP engine ID and community…
Objective: To separate management traffic from data/customer traffic in your Cisco XR routers. Preferably, Data and Management are into 2 separate network domains. Pre-requisite: UTP cables (for each RSP management port in case for switchover) are connected to a network switch to access the OOB management gateway * * Management IP Configuration* * 1. Configure the vrf for management vrf management description VRF for Out-of-Band address-family ipv4 unicast 2. Set the physical IP address on each RSP management port. There are total of…
Here is sample commands in configuring SNMPv2 and SNMPv3 in Cisco IOS-XR devices. It also detailed on how to configure SNMP traps for your Network Monitoring System. SNMPv2c community: snmpcomm123 management IP address: 192.168.10.100 SNMP Polling Server: 192.168.20.199 SNMP Trap Server: 192.168.20.200 SNMPv2c Polling Configuration: ipv4 access-list SNMP-ALLOW 10 permit ipv4 host 192.168.20.199 any snmp-server contact DC-ADMIN snmp-server location Datacentre snmp-server trap-source Loopback0 snmp-server community snmpcomm123 RO SystemOwner IPv4 SNMP-ALLOW SNMPv2c Traps Configuration: configure snmp-server traps snmp-server host 192.168.20.200 traps snmpcomm123 Verify: /usr/bin/snmpwalk -M /usr/local/snmp/mibs -v2c…
Here is sample SNMPv2 and SNMPv3 configuration in Juniper routers. It also detailed on configuring SNMP trap for your Network Monitoring System(NMS). SNMPv2c community: snmpcomm123 management IP address: 192.168.10.100 SNMP Polling Server: 192.168.20.199 SNMP Trap Server: 192.168.20.200 Configuration: set snmp name JUNIPER-SNMP set snmp description “Juniper SNMP” set snmp location Datacentre set snmp community snmp routing-instance mgmt_junos set snmp community snmpcomm123 clients 192.168.10.100/32 Traps Configuration: set snmp trap-options source-address 192.168.10.100 set snmp trap-options agent-address outgoing-interface set snmp trap-group SNMPGROUP version…
Leave a Comment